Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
How do you really feel about A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to remove the old bathtub and place the brand-new bathtub, the job is much harder. In either instance, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old tub and also set in the new one. See to it you have actually qualified yourself for the job as well as fit trying it. As opposed to working with a professional to take control of a halfway-completed job, it is far better to take into consideration using one prior to you start. Opportunities are you might require a professional plumber to make tube links.
This short article will assist you install a brand-new bathtub in your washroom if you have actually currently bought a brand-new tub and do not require to change the arrangement of your previous water supply pipelines.
Your tools and also material list must comprise the following:
Planning for the Setup
Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain pipes any water staying in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, position the bath tub in the required setting. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by examining the level and also changing the feet on the bathtub till the level checks out level.
To set up taps, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and inspect all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bathtub and also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has been used at least when as this will certainly resolve it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former type should be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, causing complications with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes and cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can split relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I hope you enjoyed our piece on How to Install a Bathtub. Thanks for taking a few minutes to read through our content. Do you know someone else who is in to the topic? Feel free to share it. I am grateful for your time. Kindly come visit our blog back soon.
Results guaranteed, contact! Report this page